Fidas mobile 氣溶膠粒徑譜儀
- 描述
- 行業應用
- 技術參數
- 視頻
- 下載
描述
The Fidas® mobile is designed to be a portable, hand-held, battery-operated device that can also be plugged into the power supply It simultaneously measures PM1, PM2.5, PM4, PM10, and TSP environmental mass fractions or respirable, thoracic, and inhalable mass fractions as per DIN EN 481. In addition, it measures the particle number and particle size distribution (upon request) in up to 64 size classes within the particle size range of 0.18 – 18 μm or 0.4 – 40 μm. The time resolution can be adjusted from one second to hourly or daily mean values for continuous measurements.
A filter holder was intentionally omitted from this model. Based on the WHO air quality guideline of 50 μg/m3 for PM10 as a daily average limit for ambient air with a volume flow of 1.4 L/min, a 48-hour measurement would have to be carried out in order to gather a concentration of 200 μg on the filter (two times the detection limit of a 100-μg laboratory scale), with the sampling time extended accordingly in the case of half the average concentration.
The Fidas® mobile is equipped with a data logger with 4 GB Compact Flash storage and WLAN support. The firmware supports complete remote access with remote maintenance and optional data storage at www.palas.de/user. In addition, the Fidas® mobile can be equipped with additional sensors for environmental conditions, temperature, atmospheric pressure, and relative humidity.
The Fidas® mobile can be connected to an isokinetic sampling probe that measures emissions in exhaust air ducts.
Principle of measurement
The Fidas® mobile measures aerosol particles based on Lorenz-Mie scattered light analysis of single particles. The single particles move through an optically differentiated measurement volume (see Fig. 1) that is homogeneously illuminated with polychromatic light.
The patented T-stop provides a precisely defined optical measurement volume and enables particle measurement without border-zone errors, resulting in a precise size measurement. The new, digitized, electronic signal analysis system enables the rapid identification and correction of coincidence, as necessary.
Fig. 1: Schematic diagram of scattered light detection with the patented T-stop
Each particle generates a scattered light impulse that is detected at an angle of 85° to 95° degrees. The particle number is measured based on the number of scattered light impulses. The level of the scattered light impulse is a measure of the particle size diameter.
Using a polychromatic light source enables a precise and unambiguous calibration curve to be obtained, resulting in an extremely high size resolution (see Fig. 2).
Fig. 2: Scattered light intensity of a white light source compared with a monochromatic light source (angle 85° – 95°, respectively; m = 1.59 + 0i)
The measured light intensities are classified to a particle diameter and combined into a histogram (corresponding to the size classes) using this unambiguous calibration curve.
In order to convert the measured particle size distribution into a mass or mass fraction, the distribution in each value is multiplied by a correlation factor that reflects the different sources (e.g. combustion aerosols, tire wear, pollen) of the environmental aerosol (see Fig. 3). A mass fraction is obtained by additionally applying the separation curve (see DIN EN 481) to the determined particle size distribution.
Fig. 3: Comparison of the algorithms for conversion of the particle size distribution by PM values
Multiple separation curves can be used simultaneously for the same size distribution, which enables the simultaneous output of PM10, PM2.5, PM1 (and others).
Operation
Based on continuous customer feedback, the user interface and software have been optimized for intuitive operation and real-time control of measurement data and parameters (see Fig. 4).
Fig. 4: Standard data screen and graphic display measurement on the integrated touch screen
In addition, the software provides data management with the integrated data logger, sophisticated export capabilities, and network support. The measured data are able to be displayed and evaluated with many available options. If a specific display is desired, we can implement it for you.
Fig. 5: Typical use of the Fidas® mobile for indoor air quality measurements
Particular Advantages
- Online display of dust values and particle size distribution
- Counting measurement method, optimal resolution
- Real-time measurement
- Light source: LED
- Up to four hours of measurement time in battery mode
- Fidas® data analyzer software for individual analysis of your measurement data on an external PC
- Low maintenance
- Easy to operate
- Reliable function
- Cloud zone via Palas server for worldwide data retrieval
- Reduces your operating expenses
Coming Soon
Coming Soon
Coming soon
相關商品
-
AATCC 127-A, AATCC 127-B, AS 2001.2.17, ASTM 751 A2, ASTM D3393, ASTM ES 21, ASTM F 1670, ASTM F 1671, ASTM F 903 C, BS 2823, BS EN 14325, DIN 53886, EDANA 120.1-80, EN 20811, EN13823, EN749, FZ/T 01004, GB 19082, GB 24539YY/T 0689, GB/T 4744, INDA IST 80.4, ISO 1420, ISO 1420 A, ISO 8096, ISO 811, JIS L 1092 A, JIS L 1092 B-b, NF G07-057, SNV 198571, WSP 80.6, YY/T 0689, YY/T 0699, YY/T 0700, 個人衛生用品, 元素分析, 兒童產品, 功能性測試, 包裝材料, 化學分析, 厚度, 可沖散性能, 器材安全性能, 回滲, 壓力及彎曲, 安全性, 實驗室用品/耗材, 實驗室用品和耗材, 尺寸穩定性和外觀, 尿片功能, 屏蔽效能, 屏蔽材料, 工業氈毯, 建築材料, 強度及撕裂, 手感及觸感, 摩擦, 木材, 橡膠/彈性體, 汽車, 汽車, 泡沫材料, 瀝青/岩土/混凝土, 無紡布, 無紡布, 無紡布, 無紡布, 無紡布, 無紡布, 無紡布, 無紡布, 無紡布, 熱傳導, 熱防護及燃燒, 熱阻,冷熱感, 玩具和兒童用品, 環境控制, 生物材料, 粘結劑, 紙張, 紡織成衣, 紫外透過率, 老化及壽命測試, 舒適性, 色牢度, 薄膜, 衝擊, 複合材料, 車內飾, 軍用特種, 軍用特種, 輕工鞋材, 透水/耐水性, 透濕,水蒸氣透過, 透血, 部件, 金屬, 防切割, 電子產品, 電池, 靜電, 鞋材, 頭盔, 顏色管理, 食品, 高可見性及逆反射
X-Rite—JG2—U35(商用光源)
加入購物車Quick View